Next, tape the cotter pin’s head to the end cap to keep it secure. After that, you need to insert a cotter pin (provided) through the end cap and torsion rod. Unfortunately, you have to repeat the first two steps for each rivet and secure the end cap to the roller tube. Once those are done you need to remove the 3 rivets by drilling a 3/16th inch hole in the center of them. Then, you need to secure the spring to stop any uncontrolled unwinding or any unintended awning movement. The first step is to open the awning only 2 revolutions. The instructions for this procedure are quite detailed but in a nutshell, here are some of the steps you need to take:
How do You Remove a Dometic Awning Motor? we have not been able to confirm this bit of information yet but that seems to be the way to go when you want to save some money.īefore you replace your motor, shop around to get the best price possible. The word is that a company called Fiamma is the company that makes these motors for Dometic and you can buy a motor directly from them for around $220. They do sell replacement motors but that price can get to around $700 which is a pretty hefty markup over the actual cost of the motor. It seems that Dometic doesn't make its own awning motors.
NEWGATE COOKHOUSEWALL CLOCK MINI BLUE SERIAL
You will need the serial or model number of the motor currently in your awning and that is usually found on the manufacturer’s badge.ĭuring our research, we did come across some interesting information. The first step in this process is to purchase the right motor for your awning. If you are still under warranty, then that is the only step you can take as any unauthorized repairs may void your protection and leave you with some expensive repair costs down the road.
This may take some mechanical skill and if you are not good with working with tools then you should call a qualified repairman to handle this problem. To avoid this issue, tilt your awning in such a way that the water will drain away from the motor. Then take your carb spray or WD-40 and use those lubricants to help break up any corrosion or rust holding the parts firmly in place. Once you have dealt with the spring, there are a couple of Allen screws that need to be removed before you can see inside the motor. You need to be careful about the spring as if you do not put it in a good spot to hold it in its current location it can unwind on you and cause you a lot more problems. Then you have to be careful with the spring. Once you have the awning in the right position, you may have to drill out 3 rivets holding the motor in place. If this happens when the awning is in the extended position, then you will have an easy time removing the motor, taking it apart, and see what parts can be cleaned and which ones need replacing.īut if the motor seizes when the awning is retracted, you may have a tough time extending the awning far enough to work on it. One of the biggest and most common problems you will find with a Dometic awning motor is that moisture got inside the casing and over time the parts corroded to the point that they would seize and not move.
That would need to be removed and replaced for the awning motor to work as it should. Make sure to check the obvious first to save you from any embarrassing moments when a repairman finds them.įinally, you may have a bad switch in the control panel. Other simple sources would be a fuse was blown or the breaker tripped for some reason. While you may be able to fix these problems yourself, it may be best to call in a qualified repairman as they have the tools to properly diagnose the problem. It can wear down over the years and simply malfunction, overheat, have a short in the wiring, and other small issues. It can malfunction due to corrosion, rust, wear and tear and again you will probably have to replace the control button.Ī third source would be the motor itself. The next common source for these two common problems would be the power button. One will be that there is a wire loose or frayed cutting the power to the motor.Īll you have to do if that is the source of the problem is replace the wire. The basic two problems you will run into will be that the awning will not retract and it will not deploy.
0 kommentar(er)
